Production of Refractory Porcelain Crucibles from Local Ceramic Raw Materials using Slip Casting

Full Text (PDF, 636KB), PP.56-69

Views: 0 Downloads: 0

Author(s)

Odewole Peter Oluwagbenga 1,* Kashim Isah Bolaji 1 Akinbogun Tolulope Lawrence 1

1. Federal University of Technology, Akure, 340252,Ondo State, Nigeria

* Corresponding author.

DOI: https://doi.org/10.5815/ijem.2019.05.05

Received: 20 May 2019 / Revised: 2 Jun. 2019 / Accepted: 12 Jun. 2019 / Published: 8 Sep. 2019

Index Terms

Refractories, Porcelain Crucibles, Mullite, Ceramic Raw Materials, Local Production.

Abstract

The vast need for refractories in Nigeria makes it imperative to domesticate its production in the country in order to reduce over-reliance on their importation. In this research, refractory porcelain crucibles were produced from indigenous ceramic raw materials from Ikere Ekiti and Awo (locations in South Western, Nigeria). Chemical analysis was carried out on the raw materials using X-ray Fluorescence Spectrometer (XRF) to determine their chemical compositions. Five body compositions, labeled as samples A-E were formulated and the crucibles were produced using slip casting. They were dried and fired in a gas kiln up to 13000C for 6 hours. The result of the standard tests carried out on the locally produced porcelain crucibles showed total shrinkage of 10%-15%, water absorption of 0.36%-0.72%, compressive strength of 1.43N/mm2-1.65 N/mm2 and refractoriness of 1680.20C-1717.50C. The result showed that ceramic raw materials sourced from the selected deposits in South Western Nigeria are suitable for the production of porcelain crucibles with good refractory properties.

Cite This Paper

Odewole, Peter Oluwagbenga, Kashim, Isah Bolaji, Akinbogun, Tolulope Lawrence. " Production of Refractory Porcelain Crucibles from Local Ceramic Raw Materials using Slip Casting ", International Journal of Engineering and Manufacturing(IJEM), Vol.9, No.5, pp.56-69, 2019. DOI: 10.5815/ijem.2019.05.05

Reference

[1]Olasupo, O. A. and Borode, J. O., Development of insulating refractory ramming mass from some Nigerian refractory raw materials. Journal of Minerals & Materials Characterization & Engineering. 2009; 8 (9): 667-678.

[2]Torres, M.M., Freestone, I.C., Hunt, A., and Rehren, T., Mass-produced mullite crucibles in medieval Europe: manufacture and material properties. J. Am. Ceram. Soc. 2008; 91 (6): 2071–2074.

[3]Söderberg, A., Metallurgic ceramics as a key to Viking Age Workshop Organization. Journal of Nordic Archaeological Science. 2004; 14:115–124.

[4]WiseGeek, What is a ceramic crucible? 2015. Available from: m.wisegeek.com/what-is-a-ceramic-crucible.htm

[5]Ovri J.E.O. and Onuoha C., Characterization of some Nigerian local clays for electrical porcelain applications. International Journal of Advanced Materials Research. 2015; 1 (3): 113-119.  

[6]Oladiji, A.O., Borode, J.O., Adewuyi, B.O., and Ohijeagbon, I.O., Development of porcelain insulators from locally sourced materials. USEP: Journal of Research Information in Civil Engineering. 2010; 7 (1): 47-58

[7]Cuesta L.C.D. and Bernardo S.T., Development of porcelain chemical crucibles from local materials. The Philipines Journal of Science. 1987; 116 (3): 327- 346.

[8]Schwartz M.A., White G.D. and Curtis C.E., Crucible handbook. United States Atomic Energy Commission. Oak Ridge National Laboratory. Oak Ridge, Tennessee; 1953.

[9]Nwobi B.E., Beneficiation of Bauchi graphite for crucible production. Master thesis, Department of Chemical Engineering Faculty of Engineering, Ahmadu Bello University, Zaria; 2006.

[10]Aye, A.E.  and Oyetunji, A., Metallurgical analysis of Ugunoda clay deposit, Nigeria for use as a refractory. International Journal of Science and Advanced Technology. 2013; 3 (10): 25-29.

[11]Apeh F.I., Esezobor D.E., and Lawal G.I., Characterization of Onibode and Owode-ketu clays for use as refractory materials in foundry industry. Journal of Engineering Research. 2011; 16 (3):69-77.

[12]Umaru M., Aliyu M.A, Mohammed I.A., and Sadiq M.M., A Comparative study on the refractory properties of selected clays in North Central Nigeria. Academic Research International. 2012; 3 (1): 393-398.

[13]Lawrence O.O. and Ayo S.A., Suitability of Nigerian rocks as refractory materials for monolithic furnace lining. Particulate Science and Technology: An International Journal. 2012; 30 (3): 209-219.

[14]Aigbodion, V.S. et al, Production of alumino-silicate clay-bonded bagasse ash composite crucible by slip casting, J. Mater. Environ. Sci. 2014; 5 (5): 1658-1666.

[15]Garkida A.D., Local raw material exploration for the production of refractory pots for melting glass. Master Thesis, Department of Industrial Design, Faculty of Environmental Design, Ahmadu Bello University, Zaria; 1998.

[16]Adamu A., Giwa Y., and Opoku E.V., Production of High Temperature Refractory Crucibles from Locally Available Clays in Nigeria. Proceedings to the 12th Annual Ceramic Researchers Association of Nigeria (CERAN) Conference and Exhibition held at Auchi Polytechnic, Auchi on 4th-8th October, 2015.

[17]Monteiro R.R., Sabioni, A.C.S., da Costa G.M., Preparation of mullite from topaz. Cerâmica. 2004; 50 (316): 318-323.

[18]Chen C.Y., Lan G.S., and Tuan W.H., Microstructural evolution of mullite during the sintering of kaolin powder compacts. Ceramics International.  2000; 26: 715-720.

[19]Ruan G., Zhang Z., Yin M., and Xu G., Effect of aluminum powder on the synthesis of corundum-mullite composites. Ceramics – Silikáty. 2013; 57 (2): 133-137.

[20]Kashim I.B., Solid mineral development in sustaining Nigeria’s economic and environmental realities of the 21st Century. Journal of Sustainable Development in Africa. 2011a; 13 (2): 210-223.

[21]Adindu, C.I., Moses, J., Thaddeus, C.A., and Tse D.T., Exploring ceramic raw materials in Nigeria and their contribution to nation’s development. American Journal of Engineering Research. 2014; 3 (9): 127-134. 

[22]Afolabi O., Olorunfemi M.O., Olagunju A.O. and Afolayan J.F., Resource quantification of a kaolin deposit using the electrical resistivity method- case study from Ikere Ekiti, SouthWest, Nigeria. Ife Journal of Science. 2004; 6 (1): 35-40. 

[23]Atanda, P.O., Oluwole, O.O., and Oladeji. T.A., Electrical porcelain production from selected Kaolin deposits in South Western Nigeria using slip casting. International Journal of Materials and Chemistry. 2012: 2 (3): 86-89.

[24]Jimoh M.T., Petrochemical studies of pegmatites around Awo, South Western Nigeria. Journal of Environmental Issues and Agriculture in Developing Countries. 2011; 3(2): 19-32.

[25]Kashim I.B., The place of ceramics today. CeramicsTECHNICAL. 2011b; 32: 89-94.

[26]American Elements. Kaolin. 2015. Accessed from: www.americanelements.com/kaolin

[27]Henrik N., The self-reliant potter: refractories and kilns. 1987. Available from: www.nzdl.org/gsdlmod.

[28]Zauro T.D.M., An evaluation of the suitability of some ceramic raw materials in Kebbi State for the production of porcelain for tableware. Journal of Industrial Design. 2010; 1:43-53.

[29]Gamelasa J.A.F., Ferrazb E. and Rochaca F., An insight into the surface properties of calcined kaolinitic clays: the grinding effect, colloids and surfaces A. Physicochem. Eng. Aspects. 2014; 455: 49–57.

[30]Hansen T., Formulating a porcelain. 2008. Available from:  https://digitalfire.com/formulating_a_porcelain_282.html.  

[31]Imerys Refractory Minerals, Calcined kaolin. 2015. Available from: www.imerysrefractoryminerals.com

[32]Odewale I.O., Obika B.M. and Tse D.T., Production and characterization of aluminosilicate refractory brick using Unwana Beach silica sand, Ekebedi and Unwana clays. British Journal of Applied Science & Technology. 2015; 5(5): 461-471.

[33]Atta A.Y., Ajayi O.A. and Adefila S.S., Synthesis of Faujasite Zeolites from Kankara Kaolin Clay. Journal of Applied Sciences Research. 2007; 3 (10): 1017-1021.

[34]Zamek, J., Clay Body Shrinkage and Absorption. Online Journal of Ceramic Industry. 2003. Available from: www.ceramicindustry.com